Product Description
Shofu Hy-Bond Glasionomer CX-Smart Luting Cement Set
The Shofu Hy-Bond Glasionomer CX-Smart Luting Cement Set is a dual-cure luting cement that comes in powder and liquid form that are mixed together to form a paste. This cement can be cured using either light or self-cure methods, providing flexibility in the cementation process. The CX-Smart Luting Cement Set is designed for permanent luting of a variety of dental restorations including crowns, bridges, inlays, onlays, and posts.
Indications
- Cementation of crowns, bridges and inlays
- Cementation of orthodontic (metal) brackets and bands
Features
- High bond strength: The cement provides a high bond strength between the restoration and the tooth, ensuring a long-lasting and durable restoration.
- Radiopacity: The cement is radiopaque, making it easy to detect and monitor the restoration on dental X-rays.
- Dual-cure: The cement is dual-cure, meaning it can be cured with either light or self-cure methods, allowing for flexibility in the cementation process.
- Easy mixing and application: The two pastes are easy to mix together and apply to the restoration and tooth.
- Low solubility: The cement has low solubility, reducing the risk of dissolution or disintegration over time.
- Biocompatible: The cement is biocompatible, minimizing the risk of adverse reactions or sensitivity.
- Versatility: The cement system can be used for the permanent luting of a variety of dental restorations, including crowns, bridges, inlays, onlays, and posts.
- Long working time: The cement has a long working time, providing ample time for the dentist to complete the cementation process.
- Consistency: The cement has a smooth and creamy consistency, allowing for easy application and adaptation to the restoration and tooth surfaces.
Specifications
Compositions
POWDER: Fluoroaluminosilicate glass, HY agent, Pigments
LIQUID: Acrylic acid tricarboxylic acid co-polymer solution, Tartaric acid, water
Storage
- Store at room temperature (1-30 °C). Avoid high temperature and high humidity. Keep away from direct sunlight.
Clinical Time: Setting time after end of mixing stipulated in ISO 9917-1 is 2’30’’
Mixing time (23 ºC / 73 ºF): 30’’
Working time (23 ºC / 73 ºF): 2’ 00” From start of mixing
Setting time (37 ºC / 99 ºF): 2’ 30” From end of mixing
Removal of set cement (rubbery consistency): 1’ 30” After seating restoration
Directions
STEP 1:
- Cleaning of cavity and abutment tooth: Thoroughly remove the temporary material. Rinse with water and dry following the standard method.
STEP 2:
- Isolation: Use a rubber dam etc to isolate the treatment area.
STEP 3:
- Try-in and preparation of a restoration: Try-in the restoration to confirm fit and adjust occlusion. Then, clean the adhesive surface of the restoration.
STEP 4:
- Pulp protection: In case of close proximity to the pulp, cap with calcium hydroxide etc.
STEP 5:
- Dispensing of Powder and Liquid: Dispense 1 scoop of Powder and 2 drops of Liquid, separately.
-Standard Powder to Liquid ratio is 2.0 g : 1.0 g
-Gently shake the powder bottle to loosen the powder before dispensing. Always use the measuring scoop provided and level off the powder for accurate dosage.
-Invert the liquid bottle prior to use to dispense drops of bubble-free liquid. The nozzle tip should not contact the mixing pad.
-Remove any liquid remaining around the tip of the nozzle with a wet gauze etc. for accurate measuring.
-Tightly close the bottle caps (powder and liquid) immediately after each use. Use extra caution to protect the powder against any possible moisture contamination.
STEP 6:
Mixing: Mix Powder and Liquid evenly with a plastic spatula within 30 sec.
Mixing time (23 °C)
| 30”
|
|
Working time (23 °C)
| 2’00”
| From start of mixing
|
Setting time (37 °C)
| Approx. 2’30”
| After seating the restoration in patient’s mouth
|
-In cases ambient temperature is higher than 23 °C,working time will be shortened, and if the temperature is lower than 23 °C, working time will be elongated.
-Do not add extra liquid while mixing to prevent degradation of the material properties.
-Do not mix powder or liquid with components of other glass polyalkenoate cements.
STEP 7:
Placement of the restoration : Apply the cement mixture evenly on the restoration surface to be cemented. Seat the restoration onto the cavity or abutment tooth. Hold in place with moderate pressure until the cement sets. Standard setting time is approximately 2’30” after placing the restoration.
-Avoid contamination of the restoration surface to be cemented. If the surface is contaminated by saliva or blood, thoroughly clean the surface with an alcohol moistened cotton ball.
STEP 8:
Removal of excess cement : Remove excess cement with an instrument after it exhibits rubber consistency (1 min. - 2 min. after placing the restoration in patient’s mouth).
Packaging
Shofu Hy-Bond Glaslonomer CX-Smart 1-1 Set:
- 1 x 45gm Powder
- 1 x 30gm Liquid
Shofu Hy-Bond Glaslonomer CX-Smart Mini Set:
- 1 x 15gm Powder
- 1 x 10gm Liquid