Product Description
GLUMA has been suffi cient to reduce and prevent hypersensitivity. The results appear quickly and effectively, without mixing, curing or multiple applications. Patients feel immediate relief. Every good restoration starts with the GLUMA Desensitizer. Its effi cacy has been proven in over 50 million restorations. It can be used with all common adhesives and restoration materials and in every treatment situation. GLUMA neither needs to be stirred or light cured. This simplifi es application and saves time.
Indications
GLUMA Desensitizer is used for the treatment of hypersensitive dentine. It achieves its effects by precipitation of plasma proteins, which reduces dentinal permeability and occludes the peripheral dentinal tubules.
This inhibits the flow of fluid through the tubules which is the cause of sensitivity.
GLUMA Desensitizer is used:
- To eliminate pain in exposed cervical areas not requiring restoration,
- To alleviate or prevent dentinal sensitivity after preparation of teeth to receive indirect restorations.
Use GLUMA below every restoration – direct and indirect – to ensure your patients the comfort they deserve.
- Below crowns
- Bridges
- Inlays and onlays
- Veneers and temporaries
- Margins around temporary crowns
- Below all direct restorations
Specifications
Harmful, contains glutardialdehyde, 2-hydroxyethyl-methacrylate
- It is a local irritant and has toxic effects
- Appropriate precautions should always be taken before using GLUMA Desensitizer
- Only dispense the smallest possible amount necessary for the treatment
- Harmful by inhalation
- Irritating to respiratory system
- Irritating to skin
- Risk of serious damage to eyes
- May cause sensitization by inhalation
- May cause sensitization by skin contact
- In case of contact with eyes, rinse immediately with plenty of water and seek medical advice
- Wear suitable gloves
- Before use, put on the protective goggles and cover the patient’s eyes to protect against splashes of material
- Do not breathe vapour/spray
- Avoid contact with skin.
GLUMA Desensitizer must not be used:
- If the necessary precautions cannot be taken or the specified application technique cannot be used
- If the patient is allergic to any of the ingredients contained in GLUMA Desensitizer
- If the pain is due to pulpitis,
- If the pulp is exposed or the dentine adjacent to the pulp is perforated
Directions
Dosage and Administration
Treatment of hypersensitive dentine
The treatment of hypersensitive dentinal surfaces is only indicated in cases of severe pain in reactions to thermal, osmotic or tactile stimuli. In cases of mild pain, alternative treatments such as desensitizing toothpastes should be used.
- Clean the dentine (e.g. with cleansing pumice), under local anaesthesia if necessary, and then rinse off with water.
- Protect mucous membranes by using a rubber dam. Make sure that GLUMA Desensitizer only comes into contact with the area to be treated.
- Apply the smallest possible amount of GLUMA Desensitizer required for treatment to the dentinal surface using pellets or brushes and then leave for 30 – 60 seconds
- Then dry the surface carefully by applying a stream of compressed air until the fluid film has disappeared and the surface is no longer shiny. Then rinse thoroughly with water
- Deep cavities and/or areas near the pulp should be covered with a suitable cavity lining before the desensitizer is applied.
If a single application of GLUMA Desensitizer does not produce sufficient and sustained pain relief, the treatment can be repeated at the same or a subsequent appointment before alternative treatments are used.
Treatment of dentine prepared to receive complete cast restorations
- Protect mucous membranes by using a rubber dam
- Remove moisture from the prepared dentine by applying a gentle stream of compressed air.
- Apply GLUMA Desensitizer with a pellet and leave for 30 – 60 seconds. Make sure that only the smallest possible amount required is applied and that it only comes into contact with the area to be treated
- Dry the dentinal surface carefully by applying a stream of compressed air, rinse off thoroughly with water and apply suction
- Cover cavities and/or areas near the pulp with suitable cavity linings before applying the desensitizer.
